People describe a tool fault the way they hear and see it during work. Below are the most common symptoms, likely causes and what the technician does. Diagnostics always reveal the exact cause.
01
The rotary hammer spins but does not hammer
WhyMost often the impact mechanism is worn, the grease has dried out, or mechanism parts are cracked. This can also happen after long work on concrete without breaks.
Check it yourselfCheck that the mode switch is fully set to hammer drilling and that the drill bit is suitable for concrete.
What we doWe disassemble the gearbox and impact mechanism, replace worn parts and grease, reassemble and test under load.
02
The angle grinder sparks and smells bad
WhyThe most common cause is worn carbon brushes or a dirty commutator. If you smell burning insulation, the rotor winding may be damaged.
Check it yourselfStop using the tool if it stinks or smokes. After unplugging it, you can clean the dust off the ventilation openings with a dry brush.
What we doWe check the carbon brushes, commutator and windings. Most often it is enough to replace the carbon brushes and clean the motor.
03
The drill does not turn on
WhyThe power cable may be damaged, the switch faulty, the carbon brushes worn or the motor burnt out. In a cordless tool – a poor contact, the charger or the battery.
Check it yourselfTry another socket or another extension cord. With a cordless tool, make sure the battery is pushed in all the way.
What we doWe test the circuit from the cable to the motor, locate the fault and replace or repair the faulty part.
04
Cordless tool drains quickly
WhyBattery cells wear out after a few years or after many deep discharges. Sometimes the battery is not at fault, but the tool’s electronics, which draw too much current.
Check it yourselfTry it with another battery of the same type, if you have one. Do not open the battery housing yourself.
What we doWe test the battery and the tool separately. If the battery is worn out, we replace it.
05
Charger does not charge or does not blink
WhyOften the charger cable breaks, a fuse blows or the board fails. Sometimes a poor contact between the battery and the charger is to blame.
Check it yourselfCheck the socket and make sure the battery contacts are dry and clean. Do not clean them with sharp objects.
What we doWe diagnose the charger and the battery, repair the charger, and resolder or replace faulty components.
06
Tool overheats and suddenly stops
WhyClogged ventilation openings, a motor covered in dust, worn bearings or excessive load. A saw or an angle grinder working with dull discs overheats faster.
Check it yourselfLet the tool cool down and check whether the disc or drill bit has become dull. With the tool unplugged from the mains, you can blow the dust out of the ventilation openings.
What we doWe clean the motor, replace worn parts and check that the mechanism turns easily and without jamming.
07
Vibrates heavily, hums or squeaks
WhyMost often worn bearings, broken gears in the gearbox or a bent shaft after a fall. It is unsafe to use such a tool – a disc or drill bit being thrown off can cause injury.
What we doWe disassemble the gearbox, inspect the mechanism, replace damaged parts and check that the shaft rotates properly.
08
Tool works intermittently
WhyMost often worn carbon brushes, a worn switch or a damaged cable where it enters the housing. A cracked cable may work only in a certain position.
Check it yourselfWithout bending the cable, inspect it for cracks or damaged insulation. If there are any, do not use the tool.
What we doWe replace the carbon brushes, repair or replace damaged parts and check the circuit contacts.
09
Speed control or rotation direction does not work
WhyA faulty switch with electronics, burnt contacts or a burnt-out control element or board. A common fault after long work under heavy load.
What we doWe repair the control section, resolder faulty components and replace damaged parts.
10
Housing broken, socket or holder snapped off
WhyThe tool was dropped from a height, was crushed or its plastic is old. The screw points and the support that holds the motor are often damaged.
What we doWe repair broken sockets, replace damaged parts and reinforce the housing so that the motor is held firmly.